Our 33 Litre Front Loading Benchtop Autoclave, available in Classic and Autofill versions, is ideal for laboratory research and is low in water. Have a question about Autoclaves, Sterilizers or Steam Generators? Our FAQ page has the answers. All the machines are supplied with a user manual but sometimes it is not consulted! Astell offer training to operators, and this is a service I recommend to ensure.

Author: Bagami Mill
Country: Czech Republic
Language: English (Spanish)
Genre: Business
Published (Last): 1 September 2016
Pages: 66
PDF File Size: 18.53 Mb
ePub File Size: 6.78 Mb
ISBN: 343-1-94219-497-1
Downloads: 61308
Price: Free* [*Free Regsitration Required]
Uploader: Arashilar

Can the air ballast system be used to speed up cooling? What one tool in your service kit bag could you not do without?

Litre Front Loading Autoclave | Astell UK

Sterilizers are dangerous if mis-used. Keep your machine regularly serviced and pay attention to the in-house maintenance advice we supply with each new machine. Astel the discharge water will be approx.

Also, since it is in the nature of the thermodynamics of the designthat during the Sterilize Stage heat transfer into the load causes the chamber to be typically 0.

Note that to avoid boiling the water in the condensate bottle of 35 and 50 litre machines, the Max Freesteam Time is 8 minutes.

The facilities available will depend upon those fitted and configured for this particular machine. This system is integral with and dependent upon the use of the Load Sensing system. University of Leeds, School of Dentistry chose a specially adapted Astell Benchtop autoclave to give them the extended cycles they need for ground Fit the roller into the clips.


If in doubt consult Astell Scientific or your local agents. This is useful for testing.

The Astell 33 – 63 Litre Benchtop Autoclave Range

The Pin Number is fixed in the factory. The chamber will cool autoflave more quickly than the load, so if the Programmable cooling lock is set to 99C the limiting factor will be the Preset Cooling Lock, This must be left set to suit the worst-case Liquid load if the autoclave is used for liquids. These will wipe any settings previously entered by the user. Allows an Astell Service Engineer remote access to the unit’s touchscreen controller, e.

Cover Interlocks Locking Bolt engagement and Cover Position are sensed by high-reliability fail-to-safety Microswitches.

Mains water supply required. Press NO unless you are prepared to perform calibration. The stages are as follows ; Note times, etc shown are illustrative and do not represent actual cycles. Heating to C These 4 switches control functions that cannot be set by the software or Configuration.

The chamber cools down naturally to this temperature, then the Cooling is activated.

The Astell 120 – 344 Litre Front Loading Autoclave Range

Only parts supplied by the manufacturer as spares or accessories will ensure compliance with the directives. The Sterilize Stage is started when the chamber temperature is 2C above the Setpoint Temperature set for the program.

It must be set to an appropriate temperature that will operate safely for all programs and loads.

The cycle begins with a pre vacuum, reducing the chamber pressure and removing the majority of air. If the printer mechanism works but no printing results – check that the paper has not been loaded upside down!


Frequently Asked Questions | Astell UK

Do you supply autoclave spare parts separately? The Astell – Litre Front Loading Autoclave Range The – asteell front loading autoclave offers five chamber sizes, increased in capacity from the top loading range. Typically it’s the larger square section autoclaves and machines fitted with a vacuum require servicing up to four times a year.

Swiftlock door closure mechanism. It is enabled in the User Configuration section. Note – Xutoclave are available from your sevice dept. AMB – Manaul 43 litres Model: Do not leave the paper end inside as it will feed back into the feed slot and damage the mechanism. You need to also purchase the 5 position shelf rack to use this option. Sign up for news. Here the Freesteam time was set to 1 Min. What are the most common causes of autoclave failure or the need for repair?

G StartDelay The Start Delay allows a delay time to be entered each time the cycle is started, from hours. Note ; – List only present if the Printer option is fitted. All device changes and signatures autoc,ave electronically logged and saved in a file format that cannot be altered in any way.